How To Program A Ford Transit Key

Ford Transit RKE Keyfob Programming

Are y'all looking for the tutorial on how to program the RKE Keyfob on your Ford Transit from the years 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, and 2015, 2016, 2017, 2018, 2019 to 2020? Please follow the instructions beneath for your guide to do the trick programming.

Ford Transit 1993-1999 RKE Keyfob Programming

1. Enter Programming Mode – Pace 1

   INSERT key into ignition and TURN from OFF to RUN/ACC.

   OFF is the position where you can remove your key, RUN/ACC is the position just shy of starting your vehicle.

2. Enter Programming Manner – Step 2

   LOCATE the Programming Connector located at the base of the Steering Wheel Column.

   The Programming Connector consists of ii wires and a plastic plug terminator with 2 pins.

   The pins volition Non be connected to anything.

3. Enter Programming Mode – Stride three

   Jump the ii pins in the Programming Connector using a suitable metal jumping wire (example – paperclip).

4. Program Remote

   Press whatever button on the remote to be programmed.

   Door locks volition cycle Lock/Unlock to confirm successful programming of the remote.

   Repeat this footstep IMMEDIATELY for whatsoever other remotes to be programmed to your vehicle.

5. Leave Programming Mode

   Plow ignition to OFF to get out Programming Manner.

   The vehicle locks will bike Lock/Unlock to indicate successful completion of programming.

6. Test Remotes

   Test all remotes. Programming is now complete.

Of import:

• Verify the following prior to post-obit these instructions:
  • Your vehicle is equipped with keyless entry, and
  • You accept a key flim-flam remote that is compatible with your vehicle.
• Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.
• You may clear your keyless entry system memory past entering programming mode as shown in the steps higher up.

Note: If your vehicle cannot enter programming mode, then you cannot program whatsoever remote.  This indicates either no keyless entry installed on the vehicle or a defective keyless entry receiver module.

Ford Transit 2000-2002 RKE Keyfob Programming

1. Fix Vehicle

   CLOSE and UNLOCK vehicle using power door locks.

2. Enter Vehicle Programming Mode

   INSERT key into Ignition and TURN from OFF to RUN viii times within 10 seconds, with the 8th fourth dimension ending in RUN. Door locks volition wheel to confirm Programming Mode.

3. Program Remote

   Within 20 seconds printing any button on first keyless remote fob. Door locks volition cycle to confirm programming.

   (Repeat immediately for any boosted remotes to be programmed.)

4. Exit Programming Mode

   Turn ignition to OFF. Locks will again cycle to point end of programming mode.

5. Exam Remotes

   Test all remotes. Programming is at present consummate.

Important:

• Verify the following prior to following these instructions:
  • Your vehicle is equipped with keyless entry, and
  • Yous have a key trick remote that is compatible with your vehicle.
• Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must programme all existing and new remotes that you wish to use on the vehicle at this fourth dimension.
• Y'all may clear your keyless entry system retentiveness by inbound programming mode as shown in the steps in a higher place.

Notation: If your vehicle cannot enter programming mode, then you lot cannot program whatever remote.  This indicates either no keyless entry installed on the vehicle or a defective keyless entry receiver module.

Ford Transit 2015-2020 RKE Keyfob Programming

1. Confirm First Programmed Cardinal – Step one

   INSERT the first previously programmed transponder key into the ignition.

2. Ostend Get-go Programmed Key – Step ii

   TURN the ignition from OFF to ON. Continue the ignition ON for at to the lowest degree 3 seconds, merely no more than than 10 seconds.

3. Confirm First Programmed Key – Step iii

   TURN the ignition OFF and REMOVE the outset key from the ignition.

4. Confirm Second Programmed Fundamental – Step 1

   After 3 seconds, but within ten seconds of turning the ignition OFF, INSERT the second previously programmed cardinal into the ignition.

5. Confirm 2d Programmed Central – Step two

   Turn the ignition from OFF to ON. Proceed the ignition ON for at least 3 seconds, only no more than than x seconds.

6. Confirm Second Programmed Central – Step 3

   TURN the ignition OFF and REMOVE the second central from the ignition.

7. Plan New Key – Footstep 1

   Later on 3 seconds but within 10 seconds of turning the ignition OFF and removing the 2nd key, INSERT the NEW un-programmed key into the ignition.

8. Program New Key – Step ii

   Plough the ignition from OFF to ON. KEEP the ignition ON for at least 6 seconds.

9. Program New Fundamental – Step 3

   REMOVE the NEW cardinal from the ignition.

   If the key was successfully programmed, it will operate the remote entry system and first the vehicle'due south engine.

   If the fundamental was NOT successfully programmed, it will NOT work the remote entry arrangement or start the vehicle'southward engine and the bulletin center will brandish "NO KEY DETECTED". Expect 20 seconds and REPEAT the process from Step one.

10. Examination Remotes

    TEST all remotes. Programming is consummate.

Important:

• Verify the following prior to following these instructions:
  • Your vehicle is equipped with keyless entry, and
  • You lot have a key fob remote that is compatible with your vehicle.
• You must accept two working transponder chip keys in order to programme a new transponder without the help of a professional.
• The central to be programming must be cut prior to beginning this programming procedure.
• To plan whatever boosted new keys, wait twenty seconds and Echo this procedure.

Notation: If your vehicle cannot enter programming manner, and then you cannot plan whatever remote.  This indicates either no keyless entry installed on the vehicle or a defective keyless entry receiver module.

Are you seeking for the tutorial that will teach y'all how to program the RKE Keyfob on your Ford Transit that was manufactured in 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, and 2015, 2016, 2017, 2018, 2019, or 2020? Please be sure you program the fob in accordance with the instructions that were but provided for yous. I have loftier hopes that you will discover this commodity useful in assisting you with programming the key fob for the Ford Transit.

Cheers very much! This tutorial was compiled and researched with Love past Erwin Salarda.

Continue Reading

Source: https://erwinsalarda.com/how-to-guide-ford-transit-rke-keyfob-programming/

Share this post